This Bryant Evolution HVAC installation in Idaho Falls, Idaho, included a new high-efficiency gas furnace, a matching central air conditioning system, a Connex communicating Wi-Fi controller, and an upgraded four-inch filter rack.

The project combined new heating and cooling equipment into one coordinated system. Rather than replacing only the furnace or air conditioner, Big Foot Heating & Cooling installed and connected several components needed to create a complete heating and cooling setup for the home.

The equipment included a Bryant Evolution gas furnace rated up to 98.3% AFUE, a Bryant Evolution air conditioning package, a Connex communicating Wi-Fi controller, and a four-inch filter rack with case filters.

Bryant Evolution HVAC Installation: High-Efficiency Furnace

The heating portion of this Bryant Evolution HVAC installation centered on a Bryant Evolution gas furnace rated up to 98.3% AFUE. AFUE, or Annual Fuel Utilization Efficiency, measures the percentage of fuel a furnace converts into usable heat over the course of a heating season.

The new furnace was paired with a Connex communicating Wi-Fi controller designed to work with compatible Bryant Evolution equipment. This type of communicating control allows the thermostat and HVAC equipment to exchange information as part of the system’s operation.

The installation also included a Legacy four-inch filter rack with case filters. The larger filter arrangement provides an accessible location for routine filter replacement and maintenance.

Technicians completed the required furnace connections, including gas piping, electrical wiring, venting, condensate drainage, and ductwork transitions. Integrating those components properly is an important part of any furnace installation.

Bryant Evolution HVAC Installation: Central Air Conditioning

The cooling portion of the Bryant Evolution HVAC installation included a Bryant Evolution central air conditioning system with an outdoor condenser and matching indoor evaporator coil.

The outdoor condenser was installed on a dedicated pad beside the home’s exterior foundation. Refrigerant lines were routed between the outdoor condenser and indoor equipment, with the necessary supporting connections completed as part of the installation.

The air conditioning work also included the electrical whip, low-voltage wiring, and condensate drainage. These connections allow the indoor and outdoor equipment to operate together as part of the home’s central cooling system.

The equipment selected for this project was listed as a Bryant Evolution 26 SEER air conditioning package. Homeowners can learn more about Bryant’s heating and cooling equipment directly from the Bryant website.

Connecting the Indoor and Outdoor HVAC Equipment

A complete Bryant Evolution HVAC installation requires more than placing new equipment in the home. The furnace, evaporator coil, outdoor condenser, refrigerant lines, electrical connections, ventilation, drainage, and thermostat controls all need to be coordinated.

For this Idaho Falls project, technicians handled the indoor furnace setup, evaporator coil connections, refrigerant piping, electrical connections, venting, and drainage. The Connex communicating controller was also integrated into the system.

The outdoor equipment was positioned beside the home, with refrigerant lines and wiring routed between the outdoor and indoor components. The installation was completed around the home’s existing layout while incorporating the new equipment.

The project also included the installation of the four-inch filter rack. Accessible filtration makes it easier for homeowners to keep up with routine filter changes, which are an important part of ongoing HVAC maintenance.

What Was Included in the HVAC Upgrade

This Bryant Evolution HVAC installation included several components that work together as one system:

• Bryant Evolution 98.3% AFUE gas furnace
• Bryant Evolution central air conditioning system
• Matching indoor evaporator coil
• Connex communicating Wi-Fi controller
• Legacy four-inch filter rack with case filters
• Refrigerant line connections
• Electrical and low-voltage connections
• Venting and condensate drainage
• Ductwork transitions and equipment connections

Coordinating these components helps ensure the new heating and cooling equipment is properly integrated rather than treating each piece as a separate installation.

Final Details of the Idaho Falls HVAC Installation

This Bryant Evolution HVAC installation brought together new heating and cooling equipment as part of one coordinated residential HVAC upgrade.

The new gas furnace provides the home’s heating equipment, while the central air conditioning system provides cooling for warmer weather. The communicating controller, upgraded filtration, refrigerant connections, drainage, and electrical work are also part of the completed installation.

When planning a furnace and air conditioning replacement, equipment efficiency is only one part of the decision. Homeowners also need to consider equipment compatibility, ductwork connections, filtration, drainage, electrical requirements, available space, and the installation itself.

Big Foot Heating & Cooling provides professional furnace installation and air conditioning installation in Idaho Falls and surrounding communities. A properly planned Bryant Evolution HVAC installation can bring multiple heating and cooling components together into one complete system designed around the home.